PS3 sixaxis/DS ps led
PS3 sixaxis/DS ps led
all this belongs to me from a different site
PS3 sixaxis ps led
Introduction
nice color in your ps button
the start of pimping your controller out
Parts Needed
- 3 volts LED - (3mm recommended) Any color
- 1/4 watts 47 Ohms Resister
- 30cm gauge wire
- PS3 controller
- Tiny Phillips screw driver
Tools Needed
solder iron 15-30 watt
solder
3mm led of your chosen color
flux
30cm wire ( depends were your putting the wire)
Difficulty rating:3/5
Average Time to Complete:1hr-2hr(depends on soldering skill)
Step By Step Tutorial
1.take apart your ps3 controller
1.1:undo the screws
push down the bottom part to unclip
1.2:unplug the battery and pull the board out from the case watching out for the r1 l1 buttons and the spacers by them
pull the thumb sticks off.
2:
solder your parts
3:ok now turn your board so the back is facing you
and find your power points(these points work on all the controller as from first to the newest )
negative(your mini usb)
positive(this picture is from the right side thumb stick)
4:now plug your battery in and press the ps button to see if the led comes on if so congrats if o light comes on check to
see if you put the wires in the right place.
5: now get your rubber thing from the front part of your case were the ps button is.
make a hole in it but make sure to not cut past the pads.(this is were the light will be coming through)
6:get your supporter and cut the middle part out this is were your leds going put it in after the cutting and glue it in place.
7:once all this is done and things are ok put your controller back together and try your led installation out to make sure you have not knocked a wire or anything
FAQ/ Troubleshooting
wire could come off if not soldered right
if resisters not put in right can stop you closing the case fully
PS3 sixaxis ps led
Introduction
nice color in your ps button
the start of pimping your controller out
Parts Needed
- 3 volts LED - (3mm recommended) Any color
- 1/4 watts 47 Ohms Resister
- 30cm gauge wire
- PS3 controller
- Tiny Phillips screw driver
Tools Needed
solder iron 15-30 watt
solder
3mm led of your chosen color
flux
30cm wire ( depends were your putting the wire)
Difficulty rating:3/5
Average Time to Complete:1hr-2hr(depends on soldering skill)
Step By Step Tutorial
1.take apart your ps3 controller
1.1:undo the screws
push down the bottom part to unclip
1.2:unplug the battery and pull the board out from the case watching out for the r1 l1 buttons and the spacers by them
pull the thumb sticks off.
2:
solder your parts
3:ok now turn your board so the back is facing you
and find your power points(these points work on all the controller as from first to the newest )
negative(your mini usb)
positive(this picture is from the right side thumb stick)
4:now plug your battery in and press the ps button to see if the led comes on if so congrats if o light comes on check to
see if you put the wires in the right place.
5: now get your rubber thing from the front part of your case were the ps button is.
make a hole in it but make sure to not cut past the pads.(this is were the light will be coming through)
6:get your supporter and cut the middle part out this is were your leds going put it in after the cutting and glue it in place.
7:once all this is done and things are ok put your controller back together and try your led installation out to make sure you have not knocked a wire or anything
FAQ/ Troubleshooting
wire could come off if not soldered right
if resisters not put in right can stop you closing the case fully
whitetop- Admin
- Posts : 53
Join date : 2012-11-08
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Thu Apr 10, 2014 8:38 am by whitetop
» European ISPs Can Stop Logging User Data, Court Rules
Thu Apr 10, 2014 8:35 am by whitetop
» Rightscorp Finds Scary Shortcut to Expose Alleged BitTorrent Pirates
Thu Apr 10, 2014 8:34 am by whitetop
» Building your first PC!
Tue Apr 08, 2014 2:05 am by SeanJM
» PS3 sixaxis/DS ps led
Sun Apr 06, 2014 6:53 am by whitetop
» How to get brightness working on a samsung n145 netbook
Sun Apr 06, 2014 6:39 am by cyberboy109
» Hot babe cpu monitor
Sun Apr 06, 2014 6:37 am by cyberboy109
» Chasing Pirates: Inside Microsoft’s War Room
Sat Dec 15, 2012 3:21 am by whitetop
» Origin and twitch tv are now partners !
Tue Nov 20, 2012 6:59 am by whitetop